ES OPTRONICS LIMITED
ES OPTRONICS LIMITED
Add to Cart
IPS LG LCD Display Panel Normally Black LM195WD2 SLA1 Frequency 60Hz Hard Coating
LM195WD2-SLA1 is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode(LED) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. It has a 19.5 inch diagonally measured active display area with HD+ resolution (900 vertical by 1600 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16.7M colors with Advanced-FRC(Frame Rate Control). It has been designed to apply the interface method that enables low power, high speed, low EMI. FPD Link or compatible must be used as a LVDS(Low Voltage Differential Signaling) chip. It is intended to support applications where thin thickness, wide viewing angle, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LM195WD2-SLA1 characteristics provide an excellent flat panel display for office automation products such as monitors.
LG Display LM195WD2-SLA1 General Features
| Brand | LG Display | Model | LM195WD2-SLA1 |
| Diagonal Size | 19.5 inch | Type | a-Si TFT-LCD , LCM |
| Pixel Format | 1600(RGB)×900 [HD+] | Configuration | RGB Vertical Stripe |
| Active Area | 433.92(H)×236.34(V) mm | Outline Dim. | 452(H)×263(V) ×11(D) mm |
| Bezel Area | 437.2(H)×239.6(V) mm | Treatment | Antiglare, Hard coating (3H) |
| Luminance | 250 cd/m² (Typ.) | Contrast Ratio | 1000:1 (Typ.) (TM) |
| View Direction | Symmetry | Response Time | 14 (Typ.)(G to G) |
| Viewing Angle | 89/89/89/89 (Typ.)(CR≥10) | Operating Mode | IPS, Normally Black, Transmissive |
| Support Color | 16.7M 72% (CIE1931) | Light Source | WLED [12S2P] , 30K hours , W/O Driver |
| Weight | 1.52/1.60Kgs (Typ./Max.) | Designed For | Desktop Monitor |
| Frame Rate | 60Hz | Touch Panel | Without |
| Interface Type | 30 pins LVDS (2 ch, 8-bit) , Connector | ||
| Power Supply | 5.0V (Typ.) | ||
| Environment | Operating Temperature: 0 ~ 50 °C ; Storage Temperature: -20 ~ 60 °C | ||
(1) The spike noise causes the miss-operation of circuits. It should be lower than following voltage : V=s200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In higher temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can not be operated its full characteristics perfectly. (8) A screw which is fastened up the steels should be a machine screw (if not, it causes metal foreign material and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) When LCMs are used for public display defects such as Yogure, image sticking can not be guarantee.
(11) LCMs cannot support “Interlaced Scan Method”
LG Display LM195WD2-SLA1 Lightting Details
| Lamp Features: | Lamp Shape | 2 strings | Lamp Type | WLED | Position | Edge light type (Right side) |
|---|---|---|---|---|---|---|
| Exchange | - | Amount | 12S2P | Life | 30K(Min.) (Hours) | |
| Lamp Electrical : | Input Current | 110/115mA (Typ./Max.) | Input Voltage | 36.8±2.4V | ||
| Consumption | 8.1/8.6W (Typ./Max.) | |||||
| Interface Features : | Position |
| Physical Type | Connector | ||
| Interface Detail : | Brand | Model | Amount | Pin Pitch | Pin Amount | Pin Assignment |
| LS Mtron | GT108-6P-H26-E3500 | 1 pcs | 1.0 mm | 6 pins | BLE-6PINS-CNAANC | |
| Backlight Driver : | No | |||||
Handling precautions for protection film
(1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane